Pull an open AP and AR listing dated your cutover day, enter each vendor credit as its own opening balance line against Accounts Payable, offset to Opening Balance Equity, and never re-post the original expense.
For the full sequence of a software change, see our guide on how to migrate accounting software without data loss. This piece covers only the credits and the open items.
What a vendor credit is in the ledger
A vendor credit is a debit balance sitting inside Accounts Payable for one vendor. You already recorded the expense when the original bill was entered. The credit reverses part of that, usually for a return, short shipment, billing error or rebate, and parks the value against what you next owe that vendor.
So the credit is not cash and not an expense. It nets against the open bills for the same vendor, which is why your AP total can look right while the detail behind it is wrong.
Exports drop credits for two reasons. Most move transactions but not the links between them, so a partly applied credit arrives unlinked or not at all. More often the migration is a trial balance, which shows Accounts Payable as one net number. A $1,240 credit vanishes into the total, and nobody notices until that vendor’s next bill arrives at full price.
The steps
- Fix a cutover date and stop entering in the old system. Everything below is “as of” that date. If entries keep arriving after it, your listings stop matching reality.
- Produce the open AP listing as of the cutover date. Run AP aging detail, dated the cutover day, showing all open items including credits and unapplied payments. Aging summary collapses to totals, so it will not do. If it hides debit balances, run an unapplied vendor credit report alongside it.
- Produce the open AR listing the same way. AR aging detail as of the cutover date, plus any unapplied customer credit memos, deposits or prepayments. Customer credits are the same mechanic in reverse.
- Prove the listings against the balance sheet. Your open AP detail, credits included and signed correctly, must sum to the Accounts Payable line on the cutover-date balance sheet. Same for AR. If they do not tie, the detail is incomplete, and entering it pushes the error forward. Our free balance sheet template sets the cutover figures beside what the new system reports.
- Enter open items as opening balances, one line per document. Every open bill at its remaining unpaid amount, every credit at its remaining unapplied amount, keyed to the right vendor with its original date and number. Never enter a net figure per vendor. That net is what you are preserving the detail behind.
- Offset to Opening Balance Equity, not to expense. This is the double-count trap. The expense was already recognized in the old system and lives in your historical profit and loss. Posting an opening bill to an expense account recognizes it twice, overstating costs.

The worked journal entry
Northgate Supply, cutover December 31. Two open bills totaling $4,800 and one unapplied vendor credit of $1,240 from a returned order. Net owed is $3,560.
| Account | Debit | Credit |
|---|---|---|
| Accounts Payable, Northgate Supply (credit memo CM-118) | 1,240.00 | |
| Opening Balance Equity | 3,560.00 | |
| Accounts Payable, Northgate Supply (bills 4471, 4502) | 4,800.00 | |
| Totals | 4,800.00 | 4,800.00 |
Debits equal credits at $4,800.00. Accounts Payable nets to a $3,560.00 credit balance, which is what you owe. The credit stays visible as its own document, so when bill 4610 arrives you can apply CM-118 against it. No expense account is touched, because no new cost occurred.
Most systems build this entry for you if you enter the bills and the credit as documents, so do that when you can. The entry above is what to check the result against, and what to post when a system will not take an opening credit as a document. GlassJar accepts one as its own document, as do most established systems.
Reconciling in the first month
Check each vendor’s statement against your new ledger, not your old one. Ask every vendor holding an open credit for a current statement, then compare three numbers: their balance, your balance for them, and the credit they show as available. Differences are nearly always a credit entered at full value when it had already been partly applied, or a payment that cleared between cutover and loading. Run the same pass on AR.
The trap: a credit applied in the old system after cutover
This one costs real money. Someone with old-system access enters a January bill there, out of habit, and the system helpfully applies the outstanding credit to it. The credit is consumed in a ledger you no longer use while your new system still shows it available. You claim it later, the vendor declines, and what you reported was never collectible.
Two controls prevent it. Set the old system to read-only on the cutover date, or remove everyone’s entry permissions. Then save a dated PDF of each open credit as evidence of what you hold. If it cannot be locked, close the credits out first: take a cash refund or apply them to a final bill, and migrate a clean zero.
FAQ
Do vendor credits expire if I switch accounting software?
Not because of the switch. A credit is an agreement with the vendor and survives whatever software you use. What you lose is the ability to prove it, so get a statement from every vendor holding a credit before cutover.
Should I enter a vendor credit as a negative bill instead?
It works where negative amounts are allowed, but it tracks badly. A negative bill sits in your payables queue and can get selected for payment. A proper credit memo stays apart until you apply it.
Why did my AP total come across right but the vendor balances are wrong?
Because the migration used a trial balance, which carries only the net figure. The total ties while the detail behind it does not exist. Enter the open AP detail document by document and let the total rebuild from it.
What offset account should opening balances hit?
Opening Balance Equity, or whatever your system calls its conversion suspense account. Once every open item is in and the balance sheet ties, clear that account to retained earnings so it ends at zero.
























